IRFP150 DATASHEET PDF

IRFP Transistor Datasheet, IRFP Equivalent, PDF Data Sheets. MOSFET. Parameters and Characteristics. Electronic Component Catalog. Fifth Generation HEXFETs from International Rectifier utilize advanced processing techniques to achieve extremely low on-resistance per. THE PRODUCT DESCRIBED HEREIN AND THIS DATASHEET ARE SUBJECT IRFP SiHFP ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless.

Author: Faurg Sakora
Country: Kosovo
Language: English (Spanish)
Genre: Love
Published (Last): 4 July 2009
Pages: 288
PDF File Size: 17.53 Mb
ePub File Size: 16.38 Mb
ISBN: 553-7-20189-881-1
Downloads: 29511
Price: Free* [*Free Regsitration Required]
Uploader: Voodoomi

Breakdown maximum Vds applies in all modes. This is very much defined as a “single pulse” bottom left corner of graph i.

Or it could mean 10 amps at 16 volts or 16 amps at 10 volts etc. Internal diode would conduct and prevent this. Is It V too? You always answer my questions in a very helpful and informative way.

IRFP (IXYS) – High Voltage Power Mosfet Die | eet

Never miss the small print, let alone the footnotes. First, I can not find the pinout diagram.

Pin assignment is buried within the mechanical drawings. Andy aka k 10 Sign up using Email and Password. What will happen if you apply V on 0. To the best of my knowlodge, the only thing that is not correct in the datasheet is the way the on-resistance is declared: When the FET is fully on, it behaves more or less like a resistor of value RdsON, which is 36 mOhm in this case, so there would be no way to have volts across it.

  HDR SR10 PDF

It’s easy to get into the habit of skipping over the last pages in a datasheet with mechanical and packaging information, it’s understandable that you missed it. If your pulse was 10 ms then you could withstand volts whilst taking no more than about 2. You can’t apply anything more than about a volt in reverse.

That’s an instantaneous power of 9 kW. Email Required, but never shown.

When Vgs is high enough, then it will enter ohmic mode and meet its RdsON spec. Thank you very much teacher Andy aka. Sign up using Facebook.

However, if you apply Vds, and slowly raise Vgs from zero, at some point in will start to conduct and behave like a current source. The X axis is voltage and you can see it is limited to volts. This is the datasheet of a mosfet and I have two issues: The most important rule about any data sheet is this: Some prefer to call this “linear mode”, since this is the mode to use when you want to make a linear amplifier or a source follower with the FET.

IRFP MOSFET N-CH V 41A TOAC Vishay IR datasheet pdf data sheet FREE from

igfp150 What is the maximum supply voltage or the maximum operating voltage? Chupacabras 3, 2 11 The current would be amperes. It is determined by the physical construction of the FET.

  HTTPD DOCS 2.2.14 EN PDF

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. See “Source-Drain Ratings and Characteristics” for numbers on page 2. Eventually if the graph showed this detail you would find that the continuous power rating of watts means a continuous current of 1. And power dissipation kW.

Thank you very much. As for the pinout, you can bet on the standard one, ie GDS. Alternatively you could withstand volts but at a reduced current of about 90 amps.

IRFP150 MOSFET. Datasheet pdf. Equivalent

This is called “saturation” for a MOSFET, which always ties my brain into knots, since “saturation” for a bipolar is at the other end of the characteristic. Lead assignments are on page 8. I don’t know where drain, source and gate are. From datasheet you can see, that maximal allowed current is 42A, and power dissipation W.

(PDF) IRFP150 Datasheet download

See also this on the last page: Yes, it is complete. If there’s missing data, the datasheet doesn’t contain it. Which pin is gate and which is drain?